Yanmar 2YM15 Service Manual Page 114
- Page / 231
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. Disassembly and reassembly
94R1
(13) Mounting the oil seal and gear case cover
1) Replace the used oil seal with a new one when the
gear case cover is disassembled.
2) Insert a new oil seal by using the oil seal insertion
tool on the position of the gear case cover end face
(61.5 0/-1 mm distance from the end of the cylinder
block). (Refer to the right figure.)
3) Apply lithium grease to the oil seal lips.
4) When wear is found on the oil seal contact part of a
crankshaft pulley, replace the pulley with a new
one. Carefully install the pulley so as not to
damage the oil seal.
5) Apply the liquid gasket to the gear case cover.
Position the two knock pins and tighten the bolts of
the gear case cover.
NOTE:
Trim the liquid gasket if it protrudes onto the oil pan
mounting surface.
(14) Mounting the lube oil inlet pipe
Mount the lube oil inlet pipe on the bottom of the
cylinder block, using new gasket.
Tightening torque N•m (kgf•m)
Lube oil inlet pipe 26 (2.6)
Crankshaft
pulley
Oil seal Gear case cover Gear case
Cylinder block
61.5
-1
0
977770
-01212
Liquid gasket
Gear case cover
Oil seal
- 3YM30/3YM20/2YM15 1
- Printed in Japan 2
- M9961-03E101 2
- California 3
- Proposition 65 Warning 3
- CONTENTS 4
- FOR SAFETY 10
- Well fitting !! 12
- 1. General 16
- 1.2 Specifications 17
- 1.3.1 Fuel oil 20
- 1.3.2 Lubricating oil 20
- 1.3.3 Cooling water 21
- 1.4 Engine outline 22
- 1.General 23
- 007018-00E 25
- 1.5 Piping diagrams 28
- 5 YDX M 1.11 P 3 N 32
- (b) Exhaust gas back pressure 33
- (a) Fuel injection nozzle 34
- (b) Fuel injection pump 34
- 2. Inspection and adjustment 35
- 2. Inspection and adjustment 36
- 2.2.1 Check before starting 37
- (4) Seawater outlet 38
- (5) Check cooling water level 38
- Sediment 40
- 10 MINUTES 41
- Alternator 42
- Belt adjuster 42
- Set bolt 42
- (Valve clearance) 43
- (Normal) (Abnormal) 43
- (Valve clearance adjustment) 44
- (Fuel filter) 45
- Battery charge measurement 48
- 20 = St + 0.007 ( t - 20 ) 49
- (Hydrometer structure) 49
- (How to read hydrometer) 49
- (Oil drain pump) 50
- Pressue cap 53
- Fresh water 53
- Coolant tankNotches 53
- To fresh water 54
- Rubber hose 54
- (L-type mixing elbow) 55
- Optional 55
- (U-type mixing elbow) 55
- Injection nozzle 58
- Nozzle tester 58
- (Abnormal spray pattern) 60
- (Normal spray pattern) 60
- NP - DN O P D N159 61
- Test pressure 62
- 0.20 MPa (2 kgf/cm 62
- (Breather system component) 63
- 2.4 Sensor Inspection 64
- 2.5 Thermostat inspection 65
- 2.6 Adjusting operation 66
- 2.7 Long storage 68
- 3. Troubleshooting 69
- Cause and Effect 77
- Countermeasure 77
- 3. Troubleshooting 79
- Compression 82
- 4. Disassembly and reassembly 84
- 4.2.1 General hand tools 85
- Local supply 1 set 86
- H = Shaft type 87
- S = Hole type 87
- 4.2.2 Special hand tools 88
- (Local supply) 89
- (Removing the coupling) 89
- (Tool 1) 90
- (Tool 2) 90
- 4.2.3 Measuring instruments 91
- (2) Use of tools 92
- Revolving shaft 94
- Reflection mark 94
- High pressure 94
- 4.2.4 Other material 95
- [Notice] 96
- 4.3.1 Disassembly 97
- (Cooling water pipes) 100
- (Seawater pump) 101
- (Removing flywheel) 104
- (21)Turning the engine over 105
- (23) Removing the oil pan 105
- (25)Removing the gear case 105
- (28) Removing the camshaft 106
- (27)Removing the idle gear 106
- (30) Removing the gear case 107
- (32)Turning the engine over 107
- (34)Removing the main bearing 108
- (35)Removing the crankshaft 108
- (36)Removing the tappets 108
- 4.3.2 Reassembly 109
- (Journal bearing cap) 110
- (Piston ring) 111
- (Ring joints) 111
- (Camshaft side gap) 112
- (Idle gear shaft) 113
- (Gear train) 113
- Lube oil inlet pipe 26 (2.6) 114
- (18) Mounting the flywheel 115
- 006757-00E 116
- 006758-00E 116
- (31) Mounting the alternator 121
- (35) Electrical Wiring 122
- (37) Filling with lube oil 122
- (39) Test running 123
- 5.1 Cylinder block 124
- 001494-00E 126
- 5.2 Cylinder head 127
- Straight-edge 128
- Thickness gage 128
- (Valve lapping tool) 129
- (Valve sink depth) 130
- (Valve sink) 130
- (4) Valve guide 131
- (Stem seal insertion) 132
- 001509-00E 132
- Free length 132
- 001511-00E 132
- (3 cylinder head) 133
- (2 cylinder head) 133
- 001515-00E 134
- 001516-00E 134
- (Refer to 2.2.2(8).) 135
- 5.3 Piston and piston pins 136
- 5.3.2 Piston pin 137
- (Ring components) 138
- (Measuring side clearance) 138
- 180°) the oil ring gap 140
- 5.4 Connecting rod 141
- (Connecting rod side gap) 142
- Plastic gauge 143
- Alignment mark (Punched mark) 143
- Matching mark 143
- (Connecting rod small end) 144
- (Inspection by color check) 145
- (Crankshaft bend measurement) 145
- (Crankshaft R machining) 146
- 5.5.2 Main bearing 147
- 5.6 Camshaft and tappets 148
- (Camshaft outside diameter) 149
- (Camshaft bend) 149
- 5.6.2 Tappets 150
- 5.7 Timing gear 151
- 5.8 Flywheel and housing 152
- 5.8.2 Damper disc 153
- 6. Fuel injection equipment 154
- (1) Service data 155
- 2) Service data for 3YM20 156
- 3) Service data for 2YM15 157
- (2) Fuel adjustment procedure 158
- (Adjustment procedure for 7)) 159
- 6.2 Fuel feed pump 165
- N•cm(kgf•cm) 166
- 001568-00E 167
- Inlet valve Outlet valve 167
- 6.3 Fuel filter 168
- 6.4 Fuel tank 169
- 7. Intake and exhaust system 170
- 7.2 Exhaust system 172
- 8. Lubrication system 173
- 8.2 Lube oil pump 174
- (Outer diameter clearance) 175
- (Side clearance) 175
- 8.3 Lube oil filter 176
- 8. Lubrication system 177
- 9. Cooling water system 178
- 9.2 Seawater pump 180
- (3) Mount the impeller 182
- 9.3 Fresh water pump 183
- Thickness gauge 184
- 001582-00E 184
- 9. Cooling water system 185
- 9.4 Heat exchanger 186
- 9.5.3 Pressure cap inspection 187
- 9.5.4 Replacing filler neck 188
- Filler cap 189
- Coolant recovery tank 189
- 9.6 Thermostat 190
- 9.7.1 Introduction 191
- 9.7.2 Description 192
- 9.7.3 Cautions 192
- 9.7.4 Assembly procedure 193
- Fixing hole 194
- Delivery nozzle 194
- 9.7.5 Cautions for assembling 195
- 9.7.6 Troubleshooting 196
- 10.1 Specifications 197
- 11. Remote control (Optional) 198
- (2) Remote control cable 199
- (3) Engine stop cable 199
- (1) Speed control 200
- (Remote control cable clamp) 201
- (KM2P-1 marine gear) 201
- (1) Shift lever adjustment 203
- (2) Throttle lever adjustment 203
- 12. Electrical system 204
- 12.1.1 Wiring diagram 205
- 12.2 Battery 206
- 12.3 Starting motor 207
- 12.3.3 Structure 208
- (2) Structure 209
- 12.4.1 Specifications 210
- Rotative direction 211
- (Standard characteristics) 212
- (Inspection of V pulley) 213
- Clearance 213
- 12.5.1 Specifications 214
- 12.5.2 Structure 215
- 12. Electrical System 217
- 12.7 Warning devices 218
- M16 x 1.5 219
- 12.8 Glow plug 220
- Stop solenoid 221
- Governor 221
- Emergency stop button 221
- 13. Service standards 222
- 13.2 Engine body 223
- (5) Tappet and push rod 224
- (1) Camshaft 224
- (3) Backlash of each gear 224
- 13.2.3 Cylinder block 225
- (4) Piston and ring 226
- (5) Connecting rod 227
- 13. Service standards 228
- 14.1 Main bolt and nut 229
- SERVICE MANUAL 230
- YANMAR CO,. LTD 231
Related products and manuals for Engine Yanmar 2YM15
Engine Yanmar 2GM20F User Manual
(69 pages)
Engine Yanmar 3YM30E Specifications
(56 pages)
(56 pages)
Engine Yanmar 6LYA-STP Specifications
(647 pages)
(647 pages)
Engine Yanmar 4JH3-TCE Specifications
(33 pages)
(33 pages)
Engine Yanmar 3JH4E User Manual
(30 pages)
(30 pages)
Engine Yanmar 4LHA-STZP User Manual
(7 pages)
(7 pages)
Engine Yanmar 3YM30E User Manual
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals